Code error mesin cuci SAMSUNG - Hallo sahabat Tukang Service AC Depok Cibubur, Jika anda sedang mencari info tentang Code error mesin cuci SAMSUNG, kami telah menyediakan info tukang service ac panggilan 24 jam di jabodetabek. mudah-mudahan isi postingan service ac ini ini dapat anda bermanfaat. oke dec, ini diainformasinya.

Alamat : Code error mesin cuci SAMSUNG
Telepon : Code error mesin cuci SAMSUNG

Code error mesin cuci SAMSUNG

Samsung Code error

	Samsung Washer Fault Codes
4E	WATER SUPPLY ERROR	Water Supply Error occurs when water level frequency does not show changes more than 100Hz or water is not supplied up to the preset water level after 10 Minutes or more at the time of initial water supply. The error status can be cleared by turning the POWER switch OFF and back ON.
5E	WATER DRAIN ERROR	5E is displayed if the water level frequency detected is 25 KHz or less in the initial phase of the UNB -detecting cycle. The Water Drain error can be cleared by turning POWER SW OFF and back ON.
oE	OVER-FLOW ERROR	Over-Flow error occurs when the water level is too high. It can be cleared by turning POWER switch OFF. Water is drained prior to POWER switch OFF. The tub is drained for 2 minutes if a frequency of more than 25 KHz is detected.
UE	UNBALANCE ERROR	Laundry load is unbalanced, manually loosen any tangled laundry. If only one item of clothing needs washing, such as a bathrobe or jeans, the final spin result might be unsatisfactory and an UE error message will be shown in the display. Unbalance error is cleared by POWER switch OFF and back ON.
HE	WATER HEATER ERROR	HE, HE1 is displayed if the water temperature rises by 7 C or more in 1 Min or by 2 C or less 20 Min after heating process has started. The error can be cleared by turning POWER switch OFF.
1 E	WATER PRESSURE SWITCH ERROR	* Generated Frequency Signal of WATER LEVEL (WIL) SIW (KHz) Normal Level = Abnormal W/L Frequency Low Level = 30.00 Khz High Level = 15.00 Khz If the same signal is detected for more than 5 seconds, it is a PRESSURE SWITCH Error. When this error occurs the drain pump will operate for 3 min. and the display will show 1 E indicating a pressure switch error.
cE	ABNORMAL WATER TEMPERATURE ERROR	e.g. If the water temperature is 50 C or more, during a Delicate or Wool cycle. At the time of initial water supply, if the water temperature is not appropriate, the display will show cE. This error can be cleared by POWER SWITCH OFF.
11 E	WATER LEAKAGE ERROR	Water Leakage error occurs when the water drains naturally, (by leakage) after the washing program starts.
tE	THERMISTOR ERROR	This error occurs when the Thermistor circuit is abnormal or a voltage of O.2v or below or, 4.5v and over is detected. This error can be cleared by POWER switch OFF.
3E	MOTOR RESTRICTION ERROR	Hall Sensor is sensed every 5OOms. 1 second after motor starts to work. If data of hall sensor is less than 2 (2RPM), the Washing motor will stop at once. During Washing and Rinsing when a motor restriction is sensed, the motor stops and then proceeds to the next water -flow action. If the motor stops working and this happens in one direction ten times, “3E” Error is displayed. During dehydrating. when a motor restriction is sensed. the motor stops working and then returns to the initial stage of the dehydration unbalance sensing cycle. After ten times, “3E” Error isdisplayed, When the motor Is told to stop because of an operating function. no error is shown. Power 81W OFF can clear the motor restriction error.
8E	OVER CURRENT ERROR	IPM fault signal (this is caused by the overload of the MICOM INTO during motor action). IPM: Integrated power module. The IPM controls the motor. If the fault (low signal) happens to be sensed even once during the washing/rinsing stage, the motor stops immediately. However, during the dehydrating stage the signal is to be sensed, when the number of signals reads more than 6 per 500ms during the Washing or Rinsing cycle action. If the motor stops working, in one direction ten times, “8E” Error is displayed. During dehydrating, when the overload is sensed, the motor stops working at once and then feeds back to the initial stage of the dehydration unbalance sensing. When the feed back has occcurred twice, Error “8E” is displayed during the dehydrating unbalance sensing, No error happens by overload sensing. When it happens at more than 800rpm, the process is stopped compulsorily. Power Switch OFF can clear the overload error.

	Samsung Dryer Fault Codes
ts	Thermistor short	Check for restricted vent. Replace thermistor
to	Thermistor open	Check for restricted vent Replace Thermistor
do	Door Open	Check connections. Replace door switch.
FE	Power Source Frequency error	Check power source
dF	Door circuit failure	Check wiring to door switch. Replace door switch
hE	Heater error	Restricted vent. Replace thermistor.
bE	Button Error	Check and / or replace PCB
od	Over dry	Sensor Bar open. Adjust time up excessively.
Et	eeprom failure	Replace Eeprom

	Samsung Dishwasher Fault Codes
4E	Water Inlet Valve	Clean and /or replace
5E	Drain problem	Check drain hoses Replace drain pump
LE	Leak	Check for leaks

	Samsung Washer Fault Codes
4E	WATER SUPPLY ERROR	Water Supply Error occurs when water level frequency does not show changes more than 100Hz or water is not supplied up to the preset water level after 10 Minutes or more at the time of initial water supply. The error status can be cleared by turning the POWER switch OFF and back ON.
5E	WATER DRAIN ERROR	5E is displayed if the water level frequency detected is 25 KHz or less in the initial phase of the UNB -detecting cycle. The Water Drain error can be cleared by turning POWER SW OFF and back ON.
oE	OVER-FLOW ERROR	Over-Flow error occurs when the water level is too high. It can be cleared by turning POWER switch OFF. Water is drained prior to POWER switch OFF. The tub is drained for 2 minutes if a frequency of more than 25 KHz is detected.
UE	UNBALANCE ERROR	Laundry load is unbalanced, manually loosen any tangled laundry. If only one item of clothing needs washing, such as a bathrobe or jeans, the final spin result might be unsatisfactory and an UE error message will be shown in the display. Unbalance error is cleared by POWER switch OFF and back ON.
HE	WATER HEATER ERROR	HE, HE1 is displayed if the water temperature rises by 7 C or more in 1 Min or by 2 C or less 20 Min after heating process has started. The error can be cleared by turning POWER switch OFF.
1 E	WATER PRESSURE SWITCH ERROR	* Generated Frequency Signal of WATER LEVEL (WIL) SIW (KHz) Normal Level = Abnormal W/L Frequency Low Level = 30.00 Khz High Level = 15.00 Khz If the same signal is detected for more than 5 seconds, it is a PRESSURE SWITCH Error. When this error occurs the drain pump will operate for 3 min. and the display will show 1 E indicating a pressure switch error.
cE	ABNORMAL WATER TEMPERATURE ERROR	e.g. If the water temperature is 50 C or more, during a Delicate or Wool cycle. At the time of initial water supply, if the water temperature is not appropriate, the display will show cE. This error can be cleared by POWER SWITCH OFF.
11 E	WATER LEAKAGE ERROR	Water Leakage error occurs when the water drains naturally, (by leakage) after the washing program starts.
tE	THERMISTOR ERROR	This error occurs when the Thermistor circuit is abnormal or a voltage of O.2v or below or, 4.5v and over is detected. This error can be cleared by POWER switch OFF.
3E	MOTOR RESTRICTION ERROR	Hall Sensor is sensed every 5OOms. 1 second after motor starts to work. If data of hall sensor is less than 2 (2RPM), the Washing motor will stop at once. During Washing and Rinsing when a motor restriction is sensed, the motor stops and then proceeds to the next water -flow action. If the motor stops working and this happens in one direction ten times, “3E” Error is displayed. During dehydrating. when a motor restriction is sensed. the motor stops working and then returns to the initial stage of the dehydration unbalance sensing cycle. After ten times, “3E” Error isdisplayed, When the motor Is told to stop because of an operating function. no error is shown. Power 81W OFF can clear the motor restriction error.
8E	OVER CURRENT ERROR	IPM fault signal (this is caused by the overload of the MICOM INTO during motor action). IPM: Integrated power module. The IPM controls the motor. If the fault (low signal) happens to be sensed even once during the washing/rinsing stage, the motor stops immediately. However, during the dehydrating stage the signal is to be sensed, when the number of signals reads more than 6 per 500ms during the Washing or Rinsing cycle action. If the motor stops working, in one direction ten times, “8E” Error is displayed. During dehydrating, when the overload is sensed, the motor stops working at once and then feeds back to the initial stage of the dehydration unbalance sensing. When the feed back has occcurred twice, Error “8E” is displayed during the dehydrating unbalance sensing, No error happens by overload sensing. When it happens at more than 800rpm, the process is stopped compulsorily. Power Switch OFF can clear the overload error.

	Samsung Dryer Fault Codes
ts	Thermistor short	Check for restricted vent. Replace thermistor
to	Thermistor open	Check for restricted vent Replace Thermistor
do	Door Open	Check connections. Replace door switch.
FE	Power Source Frequency error	Check power source
dF	Door circuit failure	Check wiring to door switch. Replace door switch
hE	Heater error	Restricted vent. Replace thermistor.
bE	Button Error	Check and / or replace PCB
od	Over dry	Sensor Bar open. Adjust time up excessively.
Et	eeprom failure	Replace Eeprom

	Samsung Dishwasher Fault Codes
4E	Water Inlet Valve	Clean and /or replace
5E	Drain problem	Check drain hoses Replace drain pump
LE	Leak	Check for leaks

Old Code	New Code	Cause	Solution	Comment
12E	bE1	Power switch fault	No contact in power switch	If fault remains a service call is advisable
18E	bE3	Switch error	Relay fault	Service call advisable
AE	13E	Signal com error	Communication error between PCB's	If problem persists a service call is advisable
bE2	14E	Button error	Press & hold the button for 1 min	If error code persists a service call is advisable
EA/EB	3E	Tacho error	Switch off the power/reconnect and try again	If error code persists a service call is advisable
	3E1	DD Motor fault	Check DD motor	Service call advisable
	3E2	DD Motor fault	Check DD motor	Service call advisable
	3E3	DD Motor fault	Check DD motor	Service call advisable
	3E4	DD Motor fault	Check DD motor	Service call advisable
E1	4E	Water supply error -Not enough water entering the W/M	Check water supply is turned on and the water hoses are not kinked	If water supply OK, a service call is advisable
4Ed	4E1	Water temp error	Feed hoses oppositely connected	Advise customer
	4E2	Water temp error	Water too hot for selected wash	Advise customer
E2	5E	Water drain error - Water not draining from W/M	Ensure that the drain hose is not kinked and the debris filter is clear, switch off the power/reconnect, the drain pump should operate to drain W/M	If problem persists a service call is advisable
	8E	Over current error	Switch off the power/reconnect and try again	If error code persists a service call is advisable
PH1	9E1	Power error	Power supply error	Advise customer
Plo	9E2	Power error	Power supply error	Advise customer
	bE	Motor TRIAC short error	Switch off the power/reconnect and try again	If error code persists a service call is advisable
E8	CE	Abnormal water temperature	Switch off the power and try again W/M may operate drain pump automatically.	If error code persists a service call is advisable
	CE	Cooling error/warning	During holding water program temp of water is over 55C	If error code persists a service call is advisable
	dE	Door open error - The door is not closed correctly	Check that the door is closed	If the door closes OK and the fault code persists then a service call is advisable
	dE1	Door lock switch error -	Check that the door is closed	If error code persists a service call is advisable
	dE2	On/Off  switch error -	Excessive heat build up in the coil due to button being  operated continuously	Advise customer, if problem persists a service call is advisable
F	FE	Fan error	Fan fault	Service call advisable
	HE	Abnormal water temperature	Thermistor sensed temp over 100C	If problem persists a service call is advisable
E5	HE1	Water heater error - Over heated	Switch off the power/reconnect and try again	If error code persists a service call is advisable
E6	HE2/6E	Water heater error - Heater not getting hot	Switch off the power/reconnect and try again	If error code persists a service call is advisable
	HOT	Air temp error/warning	Air temp higher than 70 c	Advise customer
E7	1E	Pressure switch error - Faulty part	Switch off the power and try again W/M may operate drain pump automatically for up to 3 minutes	If error code persists a service call is advisable
E9/11E	LE	Natural drain/Water leak error	Check that the level of the drain hose is not lower than the base of the W/M, check for water on the floor? If no trace of water switch off the power/reconnect and try again	If leak found and from W/M or error code persists a service call is advisable
E3	OE	Over flow error - Too much water (foam) has entered the W/M	Too much washing powder/liquid may have been added. Switch off the power/reconnect, the drain pump should operate to drain W/M	If problem persists a service call is advisable
E3	oF	Over flow abnormal	Water has reached over flow level	If problem persists a service call is advisable
	t1	In test mode	Switch off the power/reconnect	If error code persists a service call is advisable
	t2	In test mode	Switch off the power/reconnect	If error code persists a service call is advisable
EC	tE	Thermister abnormal error	Switch off the power/reconnect and try again	If error code persists a service call is advisable
	tE1	Thermostat error	Thermostat faulty	If error code persists a service call is advisable
	tE2	Thermostat error	Thermostat faulty	If error code persists a service call is advisable
	tE3	Thermostat error	Thermostat faulty	If error code persists a service call is advisable
E4	UE	Unbalanced error - The load in the drum is unbalanced	Switch off the power and rearrange or remove some of the items to be washed	A persistent error message may indicate a fault, in this case a service call is advisable

Demikianlah Artikel Code error mesin cuci SAMSUNG

Catat nomor kontak dan alamat Code error mesin cuci SAMSUNG, silahkan kontak nomor di web ini sekarang. baiklah, jangan lupa rekomendasikan jasa service ac ini.

Anda sedang membaca artikel Code error mesin cuci SAMSUNG dan artikel ini url permalinknya adalah https://tukangserviceacdepok.blogspot.com/2013/09/code-error-mesin-cuci-samsung.html Semoga artikel ini bisa bermanfaat.

Tweet